CCNA 200-301 Real Exam Questions and Answers FREE Updated on Dec 26, 2024
200-301 Ultimate Study Guide - TorrentValid
Cisco 200-301 certification exam is a comprehensive exam that covers a wide range of topics related to networking. 200-301 exam is designed to validate the skills and knowledge of an entry-level network engineer. Cisco Certified Network Associate Exam certification is highly valued in the IT industry and can lead to a variety of job roles and career advancement opportunities. If you are interested in pursuing a career in networking, the Cisco 200-301 certification exam is an excellent way to get started.
Passing the Cisco 200-301 exam is a significant achievement for any network engineer or technician. Not only does it validate their skills and knowledge in the field, but it also opens up new job opportunities and career paths. Employers in the IT industry often look for candidates who have a CCNA certification as it demonstrates their commitment to the field and their ability to work with complex network infrastructure.
Cisco 200-301 exam is an updated version of the previous CCNA exam, and it includes a new curriculum that covers the latest networking technologies, including wireless, security, and automation. 200-301 exam is designed to test your knowledge and skills in a variety of networking concepts, including network topology, network design, network protocols, and network security.
NEW QUESTION # 109
Router R1 must send all traffic without a matching routing-table entry to 192.168.1.1. Which configuration accomplishes this task?
- A. Option A
- B. Option C
- C. Option D
- D. Option B
Answer: B
NEW QUESTION # 110
Refer to Exhibit.
The loopback1 interface of the Atlanta router must reach the loopback3 interface of the Washington router.
Which two static host routes must be configured on the NEW York router? (Choose two)
- A. ipv6 route 2000::1/128 2012::1
- B. ipv6 route 2000::1/128 2012::2
- C. ipv6 route 2000::3/128 2023::3
- D. ipv6 route 2000::1/128 s0/0/1
- E. ipv6 route 2000::3/128 s0/0/0
Answer: A,C
NEW QUESTION # 111
Refer to the Exhibit.
After the switch configuration the ping test fails between PC A and PC B Based on the output for switch 1.
which error must be corrected?
- A. All VLANs are not enabled on the trunk
- B. There is a native VLAN mismatch
- C. Access mode is configured on the switch ports.
- D. The PCs are m the incorrect VLAN
Answer: B
NEW QUESTION # 112
Refer to Exhibit.
Which action do the switches take on the trunk link?
- A. The trunk forms but the mismatched native VLANs are merged into a single broadcast domain.
- B. The trunk does not form, but VLAN 99 and VLAN 999 are allowed to traverse the link.
- C. The trunk does not form and the ports go into an err-disabled status.
- D. The trunk forms but VLAN 99 and VLAN 999 are in a shutdown state.
Answer: A
Explanation:
Explanation
The trunk still forms with mismatched native VLANs and the traffic can actually flow between mismatched switches. But it is absolutely necessary that the native VLANs on both ends of a trunk link match; otherwise a native VLAN mismatch occurs, causing the two VLANs to effectively merge.
For example with the above configuration, SW1 would send untagged frames for VLAN 999. SW2 receives them but would think they are for VLAN 99 so we can say these two VLANs are merged.
NEW QUESTION # 113
Drag and Drop Question
Drag each route source from the left to the numbers on the right. Beginning with the lowest and ending with the highest administrative distance.
Answer:
Explanation:
NEW QUESTION # 114
Refer to the exhibit.
What is the effect of this configuration?
- A. The switch discard all ingress ARP traffic with invalid MAC-to-IP address bindings.
- B. Egress traffic is passed only if the destination is a DHCP server.
- C. All ingress and egress traffic is dropped because the interface is untrusted
- D. All ARP packets are dropped by the switch
Answer: A
Explanation:
Explanation
Dynamic ARP inspection is an ingress security feature; it does not perform any egress checking.
NEW QUESTION # 115
Which type of API allows SDN controllers to dynamically make changes to the network?
- A. northbound API
- B. REST API
- C. SOAP API
- D. southbound API
Answer: D
Explanation:
https://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/Data_Center/VMDC/SDN/SDN.html
NEW QUESTION # 116
Refer to the exhibit.
A network engineer must block access for all computers on VLAN 20 to the web server via HTTP All other computers must be able to access the web server Which configuration when applied to switch A accomplishes this task?
- A. Option A
- B. Option C
- C. Option D
- D. Option B
Answer: D
NEW QUESTION # 117
When OSPF learns multiple paths to a network, how does it select a route?
- A. It divides a reference bandwidth of 100 Mbps by the actual bandwidth of the existing interface to calculate the router with the lowest cost.
- B. For each existing interface, it adds the metric from the source router to the destination to calculate the route with the lowest bandwidth.
- C. It multiple the active K value by 256 to calculate the route with the lowest metric.
- D. It count the number of hops between the source router and the destination to determine the router with the lowest metric
Answer: A
NEW QUESTION # 118
Why did Branch1 router lose WAN connectivity with R1 router?
- A. The PPP multilink group is misconfigured on the Branch1 serial interfaces.
- B. The IP address is misconfigured on PPP multilink interface on the Branch1 router.
- C. The Branch1 serial interfaces are placed in a shutdown condition.
- D. The PPP multilink group is misconfigured on the R1 serial interfaces.
Answer: B
NEW QUESTION # 119
Refer to the exhibit.
If OSPF is running on this network, how does Router2 handle traffic from Site B to 10.10.13.128/25 at Site A?
- A. It sends packets out of interface Fa0/2 only.
- B. It sends packets out of interface Fa0/1 only.
- C. It load-balances traffic out of Fa0/1 and Fa0/2.
- D. It cannot send packets to 10.10.13.128/25.
Answer: D
NEW QUESTION # 120
Refer to the exhibit.
IP connectivity and OSPF are preconfigured on all devices where necessary. Do not make any changes to the IP addressing or OSPF. The company policy uses connected interfaces and next hops when configuring static routes except for load balancing or redundancy without floating static. Connectivity must be established between subnet 172.20.20.128/25 on the Internet and the LAN at 192.168.0.0/24 connected to SW1:
1. Configure reachability to the switch SW1 LAN subnet in router R2.
2. Configure default reachability to the Internet subnet in router R1.
3. Configure a single static route in router R2 to reach to the Internet subnet considering both redundant links between routers R1 and R2. A default route is NOT allowed in router R2.
4. Configure a static route in router R1 toward the switch SW1 LAN subnet where the primary link must be through Ethernet0/1. and the backup link must be through Ethernet0/2 using a floating route. Use the minimal administrative distance value when required.
Answer:
Explanation:
See the Explanation below
Explanation:
Answer as below configuration:
On R2:
Enable
Conf t
Ip route 192.168.1.0 255.255.255.0 10.10.31.1
On R1:
Enable
Conf t
Ip route 0.0.0.0 0.0.0.0 10.10.13.3
On R2
Ip route 172.20.20.128 255.255.255.128 e0/2
Ip route 172.20.20.128 255.255.255.128 e0/1
On R1
Ip route 192.168.0.0 255.255.255.0 e0/1
Ip route 192.168.0.0 255.255.255.0 10.10.12.2 3
Save all configurations after every router from anyone of these command Do wr Or Copy run start
NEW QUESTION # 121
Drag and drop the descriptions of file-transfer protocols from the left onto the correct protocols on the right.
Answer:
Explanation:
NEW QUESTION # 122
An engineer requires a scratch interface to actively attempt to establish a trunk link with a neighbor switch. What command must be configured?
- A. switchport mode dynamic auto
- B. switchport mode trunk
- C. switchport mode dynamic desirable
- D. switchport nonegotiate
Answer: A
NEW QUESTION # 123
Refer to the exhibit.
What is the next hop for traffic entering R1 with a destination of 10.1.2 126?
- A. 10.165.20.146
- B. 10.165.20.166
- C. 10.165 20.126
- D. 10.165 20.226
Answer: D
NEW QUESTION # 124
If a notice-level messaging is sent to a syslog server, which event has occurred?
- A. An ARP inspection has failed
- B. A debug operation is running
- C. A routing instance has flapped
- D. A network device has restarted
Answer: D
NEW QUESTION # 125
Which type of IPv4 address type helps to conserve the globally unique address classes?
- A. multicast
- B. loopback
- C. private
- D. public
Answer: C
NEW QUESTION # 126
An engineer is tasked to configure a switch with port security to ensure devices that forward unicasts multicasts and broadcasts are unable to flood the port The port must be configured to permit only two random MAC addresses at a time Drag and drop the required configuration commands from the left onto the sequence on the right Not all commands are used.
Answer:
Explanation:
NEW QUESTION # 127
Which of the following is the JSON encoding of a dictionary or hash?
- A. {"key", "value"}
- B. ("key": "value")
- C. ["key", "value"]
- D. {"key": "value"}
Answer: D
NEW QUESTION # 128
Using direct sequence spread spectrum, which three 2.4-GHz channels are used to limit collisions?
- A. 1,2,3
- B. 5,6,7
- C. 1,5,10
- D. 1,6.11
Answer: D
NEW QUESTION # 129
Refer to the exhibit.
Which action must be taken so that neighbofing devices rapidly discover switch Cat9300?
- A. Configure the cdp timer 10 command on switch Cat9300.
- B. Configure the cdp holdtime 10 command on switch Cat9300.
- C. Enable portfast on the ports that connect to neighboring devices.
- D. Configure the cdp timer 10 command on the neighbors of switch Cat9300.
Answer: A
NEW QUESTION # 130
Refer to the exhibit.
The New York router is configured with static routes pointing to the Atlanta and Washington sites.
Which two tasks must be performed so that the Se0/0/0 interfaces on the Atlanta and Washington routers can reach one another? (Choose two.)
- A. Configure the ipv6 route 2023::/126 2012::1 command on the Atlanta router.
- B. Configure the ipv6 route 2012::/126 2023::1 command on the Washington router.
- C. Configure the ipv6 route 2023::/126 2012::2 command on the Atlanta router.
- D. Configure the ipv6 route 2012::/126 2023::2 command on the Washington router.
- E. Configure the ipv6 route 2012::/126 s0/0/0 command on the Atlanta router.
Answer: C,D
NEW QUESTION # 131
What are two reasons lo configure PortFast on a switch port attached to an end host? (Choose two.)
- A. to enable the pod to enter the forwarding state immediately when the host boots up
- B. to protect the operation of the port from topology change processes
- C. to block another switch or host from communicating through the port
- D. to enable the number of MAC addresses learned on the port to l
- E. to prevent the port from participating in Spanning Tree Protocol operations
Answer: A,B
NEW QUESTION # 132
Drag and drop the application protocols from the left onto the transport protocols that it uses on the right
Answer:
Explanation:
NEW QUESTION # 133
Drag and Drop Question
Drag and drop the Cisco Wireless LAN Controller security settings from the left onto the correct security mechanism categories on the right.
Select and Place:
Answer:
Explanation:
Explanation:
Layer 2 Security Mechanism includes WPA+WPA2, 802.1X, Static WEP, CKIP while Layer 3 Security Mechanisms (for WLAN) includes IPSec, VPN Pass-Through, Web Passthrough ...
Reference: https://www.cisco.com/c/en/us/support/docs/wireless/4400-series-wireless-lan-controllers/106082-wlc-compatibility-matrix.html
NEW QUESTION # 134
......
Ultimate Guide to Prepare 200-301 Certification Exam for CCNA: https://www.torrentvalid.com/200-301-valid-braindumps-torrent.html
Use Real 200-301 Dumps - Cisco Correct Answers: https://drive.google.com/open?id=1Q3edhQA-X2xredgW2JBLKoYrIjDPLgvA