Verified NACE-CIP1-001 dumps Q&As - 100% Pass from TorrentValid
Pass NACE-CIP1-001 Exam in First Attempt Guaranteed 2024 Dumps!
NEW QUESTION # 32
Galvanic corrosion occurs on which of the following substrates:
- A. Wood
- B. Fiberglass Reinforced Plastic
- C. Concrete
- D. Metal
Answer: D
NEW QUESTION # 33
You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?
- A. 105 Gauge Readings resulting in 35 Spot Measurements
- B. 75 Gauge Readings resulting in 25 Spot Measurements
- C. 45 Gauge readings resulting in 15 Spot Measurements
- D. 225 Gauge Readings resulting in 75 Spot Measurements
Answer: D
NEW QUESTION # 34
ISO SA 2 is defined as:
- A. Thorough Blast Cleaning
- B. Very Thorough Blast Cleaning
- C. Near White Metal Blasting
- D. Light Blast Cleaning
Answer: A
NEW QUESTION # 35
Solvents are added to coating formulations to
- A. decrease film permeability.
- B. dissolve binders and form liquid coatings.
- C. provide color.
- D. increase film permeability.
Answer: B
NEW QUESTION # 36
Relative humidity is
- A. a measure of the amount of moisture in the air compared to saturation level.
- B. a measure of the amount of moisture in the air compared to the air temperature.
- C. the lowest temperature at which moisture forms on a steel surface.
- D. the highest temperature at which moisture forms on a steel surface.
Answer: A
NEW QUESTION # 37
A NACE Coating Inspector is permitted to transport coating material when:
- A. Asked to do so by the Coating Application team
- B. The Inspector should never transport coating material
- C. If the Inspector meets all the necessary requirements for Transportation of Dangerous Goods
- D. Asked to do so by the Owner's Representative
Answer: B
NEW QUESTION # 38
The Inspector's Log Book is generally:
- A. Shredded by the inspector upon project completion
- B. Shared with all parties upon project completion
- C. Retained by the inspector upon project completion
- D. Submitted to the client upon project completion
Answer: C
NEW QUESTION # 39
When applying Thermal Spray Coatings the specification is most likely to refence:
- A. SSPC PA 2
- B. NACE SP 0178
- C. NACE SP 0188
- D. SSPC-CS 23.00/AWS C2.23/NACE No. 12
Answer: D
NEW QUESTION # 40
ISO SA 2.5 is defined as:
- A. Thorough Blast Cleaning
- B. Near White Metal Blasting
- C. Light Blast Cleaning
- D. Very Thorough Blast Cleaning
Answer: D
NEW QUESTION # 41
Passivation can best be described as:
- A. A protective metallic oxide surface layer that slows corrosion
- B. Complete elimination pf the corrosion process
- C. A coating layer applied to the surface to inhibit corrosion
- D. Treating metal with a liquid inhibiter
Answer: A
NEW QUESTION # 42
A magnetic pull-off type gauge is a good choice when:
- A. When an intrinsically safe tool is required
- B. When working on non-ferrous metals
- C. Performing an adhesion test
- D. Accuracy is not required
Answer: A
NEW QUESTION # 43
What is the minimum spot measurement value allowed by SSPC-PA 2 in each 10 m2 (100 ft2) area?
- A. 80% of the specified minimum thickness
- B. 70% of the specified maximum thickness
- C. 90% of the specified maximum thickness
- D. 100% of the specified maximum thickness
Answer: A
NEW QUESTION # 44
A single application coating film has a measured dry film thickness (DFT) between 4 and 5 mils (between 100 and 125 microns). The volume solids of the coating immediately before application were 67%, What wet film thickness (WFT) was applied?
- A. 6 to 7 mils (150 to 175 microns)
- B. 8 to 10 mils (200 to 250 microns)
- C. 5 to 6 mils (125 to 150 microns)
- D. 10 to 12 mils (250 to 300 microns)
Answer: A
NEW QUESTION # 45
Surface profile describes:
- A. The level of surface cleanliness required after abrasive blasting
- B. The level of surface roughness required after abrasive blasting
- C. The initial condition of the surface prior to abrasive blasting
- D. The general condition of the surface required after abrasive blasting
Answer: B
NEW QUESTION # 46
Common errors that can produce inaccurate readings when using Wet Film Thickness (WFT) gauges include:
Select All That Apply
- A. Placing the gauge along the longitudinal axis
- B. Dragging a gauge through wet coating
- C. Using a damaged gauge
Answer: B,C
NEW QUESTION # 47
What is the minimum recommended distance away from an edge that an inspector should take a measurement with a dial-type magnetic pull-off Dry Film Thickness (DFT) gauge?
- A. 2.5 cm (1 inch)
- B. 6.35 cm (2.5 inch)
- C. 2.5 millimeters (.10 inch)
- D. 1 cm (.39 inch)
Answer: A
NEW QUESTION # 48
The most important factor resulting in improved job site safety is:
- A. Safety Enforcement
- B. Engineering Controls
- C. Personal Protective Equipment
- D. Situational Awareness
Answer: D
NEW QUESTION # 49
Check abrasive blast pressure with a
- A. needle pressure gauge
- B. nozzle aperature gauge
- C. replica tape
- D. surface comparator
Answer: A
NEW QUESTION # 50
......
NACE-CIP1-001 Dumps Full Questions - Exam Study Guide: https://www.torrentvalid.com/NACE-CIP1-001-valid-braindumps-torrent.html
Use Real NACE-CIP1-001 - 100% Cover Real Exam Questions: https://drive.google.com/open?id=13qOs7MoFU6bSzvmhmbZ6bL7bD1nNSqp5