[May 09, 2025] Valid N10-008 Test Answers & N10-008 Exam PDF
Valid CompTIA Network+ N10-008 Dumps Ensure Your Passing
NEW QUESTION # 255
A technician performed a manual reconfiguration of a firewall, and network connectivity was reestablished.
Some connection events that were previously sent to a syslog server are no longer being generated by the flrewal Which of Vie following should the technician perform to fix the Issue?
- A. Tune the filter for logging the severity level on the syslog server.
- B. Adjust the proper logging level on the new firewall.
- C. Activate NetFlow traffic between the syslog server and the firewall
- D. Restart the SNMP service running on the syslog server.
Answer: D
NEW QUESTION # 256
A network technician needs to resolve some issues with a customer's SOHO network.
The customer reports that some of the devices are not connecting to the network, while others appear to work as intended.
INSTRUCTIONS
Troubleshoot all the network components and review the cable test results by Clicking on each device and cable.
Diagnose the appropriate component(s) by identifying any components with a problem and recommend a solution to correct each problem.
Cable Test Results:
Cable 1:
Cable 2:
Cable 3:
Cable 4:
Answer:
Explanation:
See the Explanation for detailed information on this simulation.
Explanation
(Note: Ips will be change on each simulation task, so we have given example answer for the understanding) To troubleshoot all the network components and review the cable test results, you can use the following steps:
Click on each device and cable to open its information window.
Review the information and identify any problems or errors that may affect the network connectivity or performance.
Diagnose the appropriate component(s) by identifying any components with a problem and recommend a solution to correct each problem.
Fill in the remediation form using the drop-down menus provided.
Here is an example of how to fill in the remediation form for PC1:
The component with a problem is PC1
The problem is Incorrect IP address
The solution is Change the IP address to 192.168.1.10
You can use the same steps to fill in the remediation form for other components.
To enter commands in each device, you can use the following steps:
Click on the device to open its terminal window.
Enter the command ipconfig /all to display the IP configuration of the device, including its IP address, subnet mask, default gateway, and DNS servers.
Enter the command ping <IP address> to test the connectivity and reachability to another device on the network by sending and receiving echo packets. Replace <IP address> with the IP address of the destination device, such as 192.168.1.1 for Core Switch 1.
Enter the command tracert <IP address> to trace the route and measure the latency of packets from the device to another device on the network by sending and receiving packets with increasing TTL values.
Replace <IP address> with the IP address of the destination device, such as 192.168.1.1 for Core Switch
1.
Here is an example of how to enter commands in PC1:
Click on PC1 to open its terminal window.
Enter the command ipconfig /all to display the IP configuration of PC1. You should see that PC1 has an incorrect IP address of 192.168.2.10, which belongs to VLAN 2 instead of VLAN 1.
Enter the command ping 192.168.1.1 to test the connectivity to Core Switch 1. You should see that PC1 is unable to ping Core Switch 1 because they are on different subnets.
Enter the command tracert 192.168.1.1 to trace the route to Core Switch 1. You should see that PC1 is unable to reach Core Switch 1 because there is no route between them.
You can use the same steps to enter commands in other devices, such as PC3, PC4, PC5, and Server 1.
NEW QUESTION # 257
A network technician was recently onboarded to a company. A manager has tasked the technician with documenting the network and has provided the technician With partial information from previous documentation.
Instructions:
Click on each switch to perform a network discovery by entering commands into the terminal. Fill in the missing information using drop-down menus provided.
Answer:
Explanation:
See the Explanation for detailed information on this simulation.
Explanation
(Note: Ips will be change on each simulation task, so we have given example answer for the understanding) To perform a network discovery by entering commands into the terminal, you can use the following steps:
Click on each switch to open its terminal window.
Enter the command show ip interface brief to display the IP addresses and statuses of the switch interfaces.
Enter the command show vlan brief to display the VLAN configurations and assignments of the switch interfaces.
Enter the command show cdp neighbors to display the information about the neighboring devices that are connected to the switch.
Fill in the missing information in the diagram using the drop-down menus provided.
Here is an example of how to fill in the missing information for Core Switch 1:
The IP address of Core Switch 1 is 192.168.1.1.
The VLAN configuration of Core Switch 1 is VLAN 1: 192.168.1.0/24, VLAN 2: 192.168.2.0/24, VLAN 3: 192.168.3.0/24.
The neighboring devices of Core Switch 1 are Access Switch 1 and Access Switch 2.
The interfaces that connect Core Switch 1 to Access Switch 1 are GigabitEthernet0/1 and GigabitEthernet0/2.
The interfaces that connect Core Switch 1 to Access Switch 2 are GigabitEthernet0/3 and GigabitEthernet0/4.
You can use the same steps to fill in the missing information for Access Switch 1 and Access Switch 2.
NEW QUESTION # 258
A network administrator needs to monitor traffic on a specific port on a switch. Which of the following should the administrator configure to accomplish the task?
- A. Port security
- B. Port tagging
- C. Port mirroring
- D. Media access control
Answer: C
Explanation:
Port mirroring is a feature that allows a network technician to monitor traffic on a specific port on a switch by copying all the traffic from that port to another port where a monitoring device is connected. Port mirroring can be used for troubleshooting, analysis, or security purposes, such as detecting network anomalies, performance issues, or malicious activities. Reference: https://www.comptia.org/training/books/network-n10-008-study-guide (page 156)
NEW QUESTION # 259
Which of the following routing protocols is used to exchange route information between public autonomous systems?
- A. BGP
- B. RIP
- C. EGRIP
- D. OSPF
Answer: A
Explanation:
BGP (Border Gateway Protocol) is a routing protocol used to exchange route information between public autonomous systems (AS). OSPF (Open Shortest Path First), EGRIP (Enhanced Interior Gateway Routing Protocol), and RIP (Routing Information Protocol) are all used for internal routing within a single AS.
Therefore, BGP is the correct option to choose for this question.
References:
* Network+ N10-007 Certification Exam Objectives, Objective 3.3: Given a scenario, configure and apply the appropriate routing protocol.
* Cisco: Border Gateway Protocol (BGP) Overview
NEW QUESTION # 260
A technician is troubleshooting a workstation's network connectivity and wants to confirm which switchport corresponds to the wall jack the PC is using Which of the following concepts would BEST help the technician?
- A. Consistent labeling
- B. Inventory management
- C. Change management
- D. Network baseline
- E. Standard work instructions
Answer: A
Explanation:
Consistent labeling would be the concept that would best help the technician to confirm which switchport corresponds to the wall jack the PC is using. Consistent labeling is a practice of using standardized and descriptive labels for network devices, ports, cables, jacks, and other components. It can help with identifying, locating, and troubleshooting network issues. For example, a technician can use consistent labeling to trace a cable from a PC to a wall jack, and then from a patch panel to a switchport. Reference: https://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/Data_Center/DC_Infra2_5/DCInfra_6.html
NEW QUESTION # 261
A user is required to log in to a main web application, which then grants the user access to all other programs needed to complete job-related tasks. Which of the following authentication methods does this setup describe?
- A. TACACS+
- B. Multifactor authentication
- C. SSO
- D. RADIUS
- E. 802.1X
Answer: C
Explanation:
The authentication method that this setup describes is SSO (Single Sign-On). SSO is a technique that allows a user to log in once to a main web application and then access multiple other applications or services without having to re-enter credentials. SSO simplifies the user experience and reduces the number of passwords to remember and manage. Reference: CompTIA Network+ N10-008 Certification Study Guide, page 371; The Official CompTIA Network+ Student Guide (Exam N10-008), page 14-5.
NEW QUESTION # 262
An administrator wants to increase the availability of a server that is connected to the office network. Which of the following allows for multiple NICs to share a single IP address and offers maximum performance while providing fault tolerance in the event of a NIC failure?
- A. Spanning Tree Protocol
- B. Elasticity
- C. Multipathing
- D. First Hop Redundancy Protocol
Answer: C
Explanation:
Reference: https://docs.oracle.com/cd/E19455-01/806-6547/6jffv7oma/index.html
NEW QUESTION # 263
A network administrator is reviewing the following metrics from a network management system regarding a switchport. The administrator suspects an issue because users are calling in regards to the switchport's performance:
Based on the information in the chart above, which of the following fs the cause of these performance issues?
- A. The switchport has been up for too long
- B. The connected device is sending too many packets
- C. The connected device is exceeding the configured MTU.
- D. The connected device is receiving too many packets.
- E. The switchport does not have enough CRCs
Answer: C
NEW QUESTION # 264
A network technician needs to use an RFC1918 IP space for a new office that only has a single public IP address. Which of the following subnets should the technician use for the LAN?
- A. 198.18.10.0/24
- B. 174.16.10.0/24
- C. 127.16.10.0/24
- D. 10.10.10.0/24
Answer: D
Explanation:
The RFC1918 IP space is a set of private IP addresses that are not routable on the public Internet and can be used for internal networks. The RFC1918 IP space consists of three ranges: 10.0.0.0/8, 172.16.0.0/12, and
192.168.0.0/161 Out of the four options, only A. 10.10.10.0/24 belongs to one of these ranges, specifically the
10.0.0.0/8 range. Therefore, the technician should use this subnet for the LAN.
References1: https://en.wikipedia.org/wiki/Private_network
NEW QUESTION # 265
A security vendor needs to add a note to the DNS to validate the ownership of a company domain before services begin. Which of the following records did the security company MOST likely ask the company to configure?
- A. SRV
- B. TXT
- C. CNAME
- D. AAAA
Answer: B
Explanation:
TXT stands for Text and is a type of DNS record that can store arbitrary text data associated with a domain name. TXT records can be used for various purposes, such as verifying the ownership of a domain, providing information about a domain, or implementing security mechanisms such as SPF (Sender Policy Framework) or DKIM (DomainKeys Identified Mail). In this scenario, the security company most likely asked the company to configure a TXT record with a specific value that can prove the ownership of the domain. AAAA stands for IPv6 Address and is a type of DNS record that maps a domain name to an IPv6 address. CNAME stands for Canonical Name and is a type of DNS record that maps an alias name to another name. SRV stands for Service and is a type of DNS record that specifies the location of a service on a network.
NEW QUESTION # 266
A retail store recently acquired the store next door. The owners would like this store to support Gigabit Ethernet for up to 328ft (100m). Which of the following is the MOST cost-effective solution?
- A. Cat5
- B. Cat 6
- C. Cat 7
- D. Cat 5e
Answer: D
NEW QUESTION # 267
Which of the following is the physical security mechanism that would MOST likely be used to enter a secure site?
- A. A landing page
- B. A firewall
- C. A smart locker
- D. An access control vestibule
Answer: D
Explanation:
Reference: https://en.wikipedia.org/wiki/Mantrap_(access_control)
NEW QUESTION # 268
A company upgrades its network and PCs to gigabit speeds. After the upgrade, users are not getting the expected performance.
Technicians discover that the speeds of the endpoint NICs are inconsistent. Which of the following should be checked first to troubleshoot the issue?
- A. Speed mismatches
- B. Load balancer settings
- C. Devices' duplex settings
- D. Office wiring category
Answer: C
Explanation:
Explanation
Duplex settings determine how data is transmitted and received over a network. If the devices have inconsistent duplex settings, such as half-duplex and full-duplex, they may experience performance issues, collisions, and errors. To troubleshoot the issue, the technicians should check the devices' duplex settings and make sure they match the network's configuration.
References:
Gigabit Ethernet does not work - Microsoft Community1
Network Tests: Are We Getting Gigabit Performance? - Tom's Hardware2
CompTIA Network+ N10-008 Exam Objectives
https://www.comptia.org/certifications/network#examdetails
NEW QUESTION # 269
A Chief Executive Officer and a network administrator came to an agreement With a vendor to purchase new equipment for the data center A document was drafted so all parties would be Informed about the scope of the project before It started. Which of the following terms BEST describes the document used?
- A. Project charter
- B. Non-disclosure agreement
- C. Memorandum of understanding
- D. Contract
Answer: A
Explanation:
The document used to inform all parties about the scope of the project before it starts is likely a project charter.
A project charter is a document that outlines the key aspects of a project, including the project's objectives, scope, stakeholders, and resources. It serves as a formal agreement between the project team and the stakeholders, and helps to define the project's goals and constraints.
A project charter typically includes information about the project's scope, including the specific deliverables that are expected and any constraints or limitations that may impact the project. It may also include details about the project team and stakeholders, the project schedule and budget, and the roles and responsibilities of each party.
By creating a project charter, the Chief Executive Officer and the network administrator can ensure that all parties involved in the project have a clear understanding of the project's goals and objectives, and can help to prevent misunderstandings or miscommunications during the project.
What is in a project charter?
A project charter is a formal short document that states a project exists and provides project managers with written authority to begin work. A project charter document describes a project to create a shared understanding of its goals, objectives and resource requirements before the project is scoped out in detail.
What are the 5 elements of the project charter?
What Are the Contents of a Project Charter? A project charter should always include an overview, an outline of scope, an approximate schedule, a budget estimate, anticipated risks, and key stakeholders
NEW QUESTION # 270
A customer is hosting an internal database server. None of the users are able to connect to the server, even though it appears to be working properly. Which of the following is the best way to verify traffic to and from the server?
- A. nmap
- B. Protocol analyzer
- C. Speed test
- D. ipconfig
Answer: B
Explanation:
A protocol analyzer is the best way to verify traffic to and from the server. A protocol analyzer, also known as a packet sniffer or network analyzer, is a tool that captures and analyzes the network packets that are sent and received by a device. A protocol analyzer can show the source and destination IP addresses, ports, protocols, and payload of each packet, as well as any errors or anomalies in the network communication. A protocol analyzer can help troubleshoot network connectivity issues by identifying the root cause of the problem, such as misconfigured firewall rules, incorrect routing, or faulty network devices12.
To use a protocol analyzer to verify traffic to and from the server, the customer can follow these steps:
* Install a protocol analyzer tool on a device that is connected to the same network as the server, such as Wireshark3 or Microsoft Network Monitor4.
* Select the network interface that is used to communicate with the server, and start capturing the network traffic.
* Filter the captured traffic by using the IP address or hostname of the server, or by using a specific port or protocol that is used by the database service.
* Analyze the filtered traffic and look for any signs of successful or failed connection attempts, such as TCP SYN, ACK, or RST packets, or ICMP messages.
* If there are no connection attempts to or from the server, then there may be a problem with the network configuration or device settings that prevent the traffic from reaching the server.
* If there are connection attempts but they are rejected or dropped by the server, then there may be a problem with the server configuration or service settings that prevent the traffic from being accepted by the server.
The other options are not the best ways to verify traffic to and from the server. nmap is a tool that can scan a network and discover hosts and services, but it cannot capture and analyze the network packets in detail.
ipconfig is a command that can display and configure the IP settings of a device, but it cannot monitor or test the network communication with another device. Speed test is a tool that can measure the bandwidth and latency of a network connection, but it cannot diagnose or troubleshoot specific network problems.
NEW QUESTION # 271
......
N10-008 Dumps Real Exam Questions Test Engine Dumps Training: https://www.torrentvalid.com/N10-008-valid-braindumps-torrent.html
N10-008 exam dumps and online Test Engine: https://drive.google.com/open?id=1gBQxN1TNpYBMvEos6YvbCe2nhYU_TlrE