Get Latest [Jan-2022] Conduct effective penetration tests using TorrentValid NACE-CIP2-001
Penetration testers simulate NACE-CIP2-001 exam PDF
NEW QUESTION 37
The HATE adhesion tester uses
- A. a special tape to apply pressure to the test dolly.
- B. mechanical means only to apply pressure to the test dolly.
- C. a hydraulic piston to apply pressure to the test dolly.
- D. compressed air to apply pressure to the test dolly.
Answer: C
NEW QUESTION 38
Surface preparation methods for Non-ferrous metals are:
- A. Not required
- B. The same for all Non-FetT0us metals
- C. The same as for Ferrous metals
- D. Specific for each type of Non-ferrous metal
Answer: D
NEW QUESTION 39
Coating application to concrete substrates is:
- A. The same as coating steel
- B. Not required as Concrete is inorganic
- C. More challenging than coating steel
- D. Less challenging, than coating steel
Answer: C
NEW QUESTION 40
As a NACE Level 2 Inspector on a field job; prior to submission your documentation should always reviewed and approved by:
- A. A NACE Protective Coating Specialist
- B. Another NACE Level 2 Inspector
- C. A NACE Level 3 Inspector
- D. A NACE Level 1 Inspector
Answer: C
NEW QUESTION 41
When measuring the Dry Film Thickness Of liquid coatings applied to galvanized ferrous substrates the most commonly used instrument is the:
- A. Magnetic Gauge
- B. Ultra Sonic DFT Gauge
- C. Tooke Gauge
- D. Eddy Current Gauge
Answer: C
NEW QUESTION 42
A single component water borne acrylic coating cures by:
- A. Oxidation
- B. Co-Reaction
- C. Coalescence
- D. Solvent Evaporation
Answer: C
NEW QUESTION 43
When conducting inspections the Inspector should follow which standards:
- A. NACE and SSPC standards in North America
- B. Australian standards in Australia
- C. ISO standards in Europe and Asia
- D. The specified standards
Answer: D
NEW QUESTION 44
When performing an adhesion test in accordance with ASTM D 3359 where the Dry Film Thickness is approximately 10 mils, the Inspector should use:
- A. Method B - X cut
- B. Method A - Cross Hatch
- C. Method B - Cross Hatch
- D. Method A - X Cut
Answer: D
NEW QUESTION 45
Coating surveys may include which steps?
Select All That Apply:
- A. Summarize the collected data
- B. Develop a survey plan
- C. Schedule the remedial work
- D. Evaluate the coatings performance
Answer: A,B,C,D
NEW QUESTION 46
In the event of a conflict between the Product Data Sheet and the Specification:
- A. It is up to the Inspector to decide which one to follow
- B. The Product Data Sheet prevails
- C. It is up to the Applicator to decide which one to follow
- D. The Specification prevails
Answer: D
NEW QUESTION 47
Pre-cleaning of work pieces will NOT remove
- A. oil or grease.
- B. dirt.
- C. mill scale.
- D. snow, ice or water.
Answer: C
NEW QUESTION 48
NACE No.13/ SSPC 6 identifies the use of:
- A. Abrasive blasting only
- B. Various methods of cleaning
- C. Watterjetting only
- D. Steam cleaning only
Answer: B
NEW QUESTION 49
When observing design defects the NACE Inspector should:
- A. Document the defect and the potential problems that could result
- B. Ignore the defect as the inspector can't change the design
- C. Stop the job immediately
- D. Request that the item be rebuilt with a better design for coating
Answer: A
NEW QUESTION 50
An Inspection and Test Plan is required when:
- A. When the Owner specifies one
- B. It is always required
- C. When the Coating Applicator requests one
- D. When the Inspector requests one
Answer: B
NEW QUESTION 51
You are NACE Level 2 Inspector working on a tank lining job where a mobile centrifugal blast unit is being used to blast the tank floor to a NACE No.1/SSPC SP 5. The Contractor has completed his final blast and has called for a hold point inspection. This is the 1 st time you have seen field based centrifugal blast cleaning. You observe what appears to be staining on the substrate however the Contractor assures you this is normal when using centrifugal blast units and what you are seeing is what is defined in the standard as an acceptable variation in appearance.
Your FIRST preferred course of action is to:
- A. Shut the job down
- B. Review the standard with the Contractor and re-inspect the floor
- C. Request that the Contractor re-blast the floor
- D. Call your supervisor
Answer: B
NEW QUESTION 52
Centrifugal blast cleaning requires:
- A. A large volume of air to propel the abrasive
- B. The use of single use abrasives
- C. Very large nozzles
- D. Well maintained blast wheels
Answer: D
NEW QUESTION 53
Coating Surveys are legally required:
- A. On high pressure gas lines and fireproofed structures
- B. On water tanks and potable water pipelines
- C. On food and beverage vessels and can linings
- D. On commercial marine vessels and offshore platforms
Answer: D
NEW QUESTION 54
Linings are used on the interior of pipelines to
- A. afford limited temperature insulation.
- B. protect the transported product.
- C. reduce magnetic polarity.
- D. provide protection against soil chemicals.
Answer: B
NEW QUESTION 55
All of these are advantages of using repair patches EXCEPT
- A. special tools or equipment are required.
- B. excellent abrasion resistance.
- C. inert to common acids, alkalis, and solvents.
- D. barrier to moisture and corrosion.
Answer: A
NEW QUESTION 56
You are the NACY Coating Inspector on a tank lining project where desiccant dehumidification is being used. Since the first shift of abrasive blasting your readings have indicated relative humidity below 40%; however on the second shift of coating application your readings are indicting 80%.
Your FIRST preferred course of action is to:
- A. Check to See if the dehumidification equipment is operating correctly
- B. Document the readings at the end of the shift
- C. Advise the coating applicator supervisor of your readings
- D. Call your supervisor
Answer: C
NEW QUESTION 57
The number of air turns in an enclosure can be affected by all of these EXCEPT
- A. type of dehumidification equipment (refrigerant or desiccant).
- B. time of the year (winter/summer).
- C. manufacturer of the equipment.
- D. coating type.
Answer: D
NEW QUESTION 58
Measuring methyl ethyl ketone (MEK) resistance of ethyl silicate inorganic zinc-rich primers by solvent rub requires
- A. 25 double rubs with a saturated cloth.
- B. 35 single rubs with a saturated cloth.
- C. 25 single rubs with a saturated cloth.
- D. 50 double rubs with a saturated cloth.
Answer: D
NEW QUESTION 59
Which type of pipelines collect the gas from the transmission system so utility companies can distribute the gas to end users?
- A. Distribution
- B. Transmission
- C. Midstream
- D. Gathering
Answer: A
NEW QUESTION 60
......
Tested Material Used To NACE-CIP2-001 Test Engine: https://www.torrentvalid.com/NACE-CIP2-001-valid-braindumps-torrent.html
Steps Necessary To Pass The NACE-CIP2-001 Exam: https://drive.google.com/open?id=1twHvhIUjZ5BcdTA2yvtp7zOjT8zeQktl