300-610 Premium PDF & Test Engine Files with 172 Questions & Answers
Get 100% Real 300-610 Exam Questions, Accurate & Verified Answers As Seen in the Real Exam!
NEW QUESTION 69
Which element is the main functional component of the architecture that separates the internal fabric and the external network that connects sites when VXLAN EVPN is deployed multisite?
- A. service leaf
- B. service gateway
- C. border gateway
- D. border leaf
Answer: C
NEW QUESTION 70
Which two methods mitigate congestion in a SAN network? (Choose two.)
- A. Configure the port channel to enable individual buffer-to-buffer credits.
- B. Configure the flow control for the FC to use R_RDY.
- C. Configure the port monitor to allow categorization of a specific device as slow.
- D. Use the port-monitor command to detect slow drain devices.
- E. Configure ER_RDY to allow splitting of each ISL between switches into separate virtual links.
Answer: C,D
NEW QUESTION 71
A network engineer must design a data center network with four Cisco Nexus 7706 switches. The switches will be installed in primary and secondary data centers in vPC domains. The two data centers must be connected via Layer 2 links and provide the maximum throughput, redundancy, and avoid port-blocking spanning-tree design.
Which deployment model meets these requirements?
- A. single-sided dual vPC
- B. dual-sided single vPC
- C. dual-sided dual vPC
- D. single-sided single vPC
Answer: C
NEW QUESTION 72
An engineer must connect an existing Cisco Fabric Interconnect to an IP-based storage array. The connection be a channel made directly between the fabric interconnect expansion module and the storage array. The engineer must also consider that the environment is running FCoE for storage and uses QoS to prioritize traffic. Which port type should be used to meet these requirements?
- A. Network
- B. server
- C. Appliance
- D. Uplink
Answer: C
Explanation:
Reference:
NEW QUESTION 73
Which type fields can an engineer use to identify an iSCSI participant? (Choose two.)
- A. hostname
- B. port number
- C. type
- D. identifying tag
- E. preshared key
Answer: A,B
NEW QUESTION 74
Which mode must be enabled on a Cisco UCS Fabric Interconnect to connect directly to a storage array?
- A. FC switching mode
- B. FC end-host mode
- C. NPIV mode
- D. NPV mode
Answer: A
NEW QUESTION 75
Drag and drop the feature descriptions from the left onto the correct UCS Fabric Interconnect modes on the right.
Answer:
Explanation:
NEW QUESTION 76
A Cisco UCS chassis with several blade servers, a pair of IOMs, and a pair of Cisco UCS Fabric Interconnects are installed in a data center.
Which two high-availability architectures are recommended between the IOMs and fabric interconnects? (Choose two.)
- A. Any combination of one to eight links are supported to be used between each IOM and fabric interconnect.
- B. One, two, four and eight links are supported to be used between each IOM and fabric interconnect.
- C. The lOMs are connected with multiple straight and cross-connect links toward a pair of nonclustered fabric interconnects.
- D. IOM is connected to the fabric interconnect that is acting as fabric A. and IOM B is connected to the fabric interconnect that is acting as fabric B.
- E. Straight and cross-connect links should be used between the lOMs and fabric interconnects to offer higher availability.
Answer: A,C
NEW QUESTION 77
A network engineer must design a Cisco HyperFlex solution based on these requirements:
* two clusters in the main data center consisting of five HyperFlex nodes
* one edge node tor the remote branch
* cluster nodes that use one rack unit of space
Which two devices should be used in the remote branch cluster for this design? (Choose two.)
- A. UCS B200
- B. Fabric Interconnect 6300
- C. HX240c
- D. Gigabit Ethernet Switch
- E. HX220c
Answer: D,E
Explanation:
HX240 is excluded because it is 2RU, while the requirement is to have one rack unit of space.
UCS B200 and FI 6300 are excluded because the solution is required in a branch.
NEW QUESTION 78
Which mode must be enabled on a Cisco UCS Fabric Interconnect to connect directly to a storage array?
- A. FC switching mode
- B. FC end-host mode
- C. NPIV mode
- D. NPV mode
Answer: A
Explanation:
Section: Storage Network Design
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/ucs-manager/GUI-User-Guides/ Storage-Mgmt/3-1/b_UCSM_GUI_Storage_Management_Guide_3_1/ b_UCSM_GUI_Storage_Management_Guide_3_1_chapter_01110.html
NEW QUESTION 79
Drag and drop the configurations from the left onto the correct policies on the right.
Answer:
Explanation:
NEW QUESTION 80
Which two configurations allow for routing traffic between two VDCs? (Choose two.)
- A. Connect the VDCs to an external Layer 3 device.
- B. Create VRF-aware software infrastructure interfaces.
- C. Cross-connect the ports between the VDCs.
- D. Create a policy map in the default VDC that routes traffic between the VDCs.
- E. Create interfaces in the VDC that can be accessed by another VDC.
Answer: A,C
Explanation:
The Cisco NX-OS software does not support direct communication between VDCs on a single physical device. You must make a physical connection from a port allocated to one VDC to a port allocated to the other VDC to allow the VDCs to communicate.
NEW QUESTION 81
Drag and drop the SAN components from the left onto the correct design considerations on the right.
Answer:
Explanation:
NEW QUESTION 82
An engineer finishes the initial set up of a VXLAN EVPN network. The engineer is asked to plan for external connectivity that supports redundancy and extends multiple virtual routing and forwarding domains. The requirement is to use the same default gateway addressing across all leaf switches that belong to the VXLAN network.
Which two solutions must be used to meet these requirements? (Choose two.)
- A. Spanning Tree Protocol
- B. VRF-Lite
- C. Inter-Site Network
- D. DC Interconnect
- E. Distributed Anycast Gateway
Answer: D,E
NEW QUESTION 83
Which feature must be configured to connect a classical Ethernet network to a data center network so that the data center network appears to be one large switch.
- A. UDLD
- B. VPC+
- C. EVPN
- D. OSPF
Answer: C
NEW QUESTION 84
Which two configurations allow for routing traffic between two VDCs? (Choose two.)
- A. Connect the VDCs to an external Layer 3 device.
- B. Create VRF-aware software infrastructure interfaces.
- C. Create a policy map in the default VDC that routes traffic between the VDCs.
- D. Create interfaces in the VDC that can be accessed by another VDC.
- E. Cross-connect the ports between the VDCs.
Answer: A,C
Explanation:
Section: Network Design
NEW QUESTION 85
An engineer is implementing management access to a Cisco Nexus platform. The customer requires a solution that provides isolation between the data and control planes. In addition to management that uses encryption and authentication. The customer will manage the device using both IPv4 and IPv6. Which two components should be used to meet these requirements (Choose two.)
- A. SNMP
- B. Telnet protocol
- C. mgmt0 interface
- D. SSM protocol
- E. SVI interface
Answer: A,C
Explanation:
We are talking about management only, so SSM is out. Since we need to separate between data and control plane, we should use mgmt0 interface, so SVI interface is out. Since we need to use encryption and authentication, this can be done in SNMPv3, while telnet does not support encryption, so telnet is out.
NEW QUESTION 86
Refer to the exhibit.
Which template is used when a vHBA template pair is created for a specific server that inherits its attributes from an existing template?
- A. Primary
- B. Secondary
- C. Updating
- D. Initial
Answer: D
NEW QUESTION 87
A network design must include a solution to run CLI commands remotely on Cisco Nexus 9000 Series Switches. The customer's security policy requires secure login credentials and an encrypted underlying transport. The command output will be processed using tools that support XML or JSON encoding. Which two components should be included in the design? (Choose two.)
- A. HTTP
- B. SSH
- C. HTTPS
- D. NX-API
- E. Bash shell
Answer: B,C
NEW QUESTION 88
What are two reasons to select OTV as the DCI solution to connect multisite topologies? (Choose two.)
- A. It constrains HSRP hello messages to each data center.
- B. It is an open standard.
- C. Layer 3 failures do not propagate beyond the OTV edge device.
- D. It propagates hosts reachability without support of traffic flooding.
- E. It extends the spanning tree between data centers.
Answer: C,E
NEW QUESTION 89
Refer to the exhibit.
A Cisco UCS chassis that has two IOMs is discovered. The chassis discovery policy creates a fabric port channel. What is the result of this policy?
- A. Cisco UCS Manager creates a single fabric port channel.
- B. Each uplink that connects an IOM is configured as a discrete link.
- C. The port channel is disabled until an administrator enables it manually.
- D. Cisco UCS Manager creates two separate fabric port channels.
Answer: D
NEW QUESTION 90
Which Cisco HyperFlex feature provides virtual machine-level cost scaling for desktop virtualization growth?
- A. HyperFlex Edge support
- B. fabric interconnects
- C. encryption offload cards
- D. dedicated compute nodes
Answer: A
NEW QUESTION 91
An engineer must integrate Layer 4 to Layer 7 services within Cisco ACI Fabric. The main requirement is to have a single point of configuration for network elements and firewall policies.
Which action meets these requirements?
- A. Define the service graph model as service policy mode.
- B. Define the service graph model as network policy mode.
- C. Deploy the firewalls in routed mode with PBR.
- D. Deploy the firewalls in transparent mode.
Answer: A
NEW QUESTION 92
......
300-610 Premium Files Practice Valid Exam Dumps Question: https://www.torrentvalid.com/300-610-valid-braindumps-torrent.html
Practice with 300-610 Dumps for CCNP Data Center Certified Exam Questions & Answer: https://drive.google.com/open?id=1yWsSp5Y5w72onQZbl5VHLYSQPE3IxiAX